青草草在线视频免费观看19,亚洲熟女av中文字幕网,久久综合九色综合久99

聯系我們

18560023440

王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間

業內資訊

玉石雕刻機臺面不平，主軸發出噪音如何處理？

來源：http://www.840505.com 時間：2021-04-02

玉石雕刻機臺面不平，是不能完成浴室的雕刻的，所以在購買設備時一定要注意這一問題，面對玉石雕刻機主軸發出噪音這個問題，要分清楚噪音，然后選擇具體的方法作出解決。下面就由小編來給大家詳細介紹一下玉石雕刻機臺面不平，主軸發出噪音如何處理？

Jade carving machine table is uneven, can not complete the bathroom carving, so in the purchase of equipment must pay attention to this problem, in the face of jade carving machine spindle noise this problem, we must first distinguish the noise, and then choose a specific method to solve. The following is a detailed introduction of jade carving machine by Xiaobian. How to deal with the noise from the spindle?

一、玉石雕刻機臺面不平怎么辦?

1、 Jade carving machine table uneven how to do?

1、玉石雕刻機如果是臺面不平的話，那么只能找廠家解決了雕刻機臺面是平的但是墊板不平了要么更換墊板，要么把墊板銑平。雕刻機臺面不平怎么預防呢?雕刻機運行的時候，直接把刀具定在雕刻機臺面上，這樣可以保證刀始終下到臺面上，不損壞臺面。

1. If the table of jade carving machine is uneven, we can only find the manufacturer to solve the problem that the table of carving machine is flat, but the base plate is uneven. Either replace the base plate or mill the base plate flat. How to prevent the uneven surface of engraving machine? When the engraving machine is running, the cutter is directly fixed on the surface of engraving machine, which can ensure that the cutter is always on the surface without damaging the surface.

2、具體的操作方式是計算路徑的時候，不要根據資料的厚度來設置“雕刻深度”而是直接設置為“0mm生產G代碼文件前，可以將“抬刀深度”設置為：抬刀高度+切割資料厚度。

2. When calculating the path, do not set the "engraving depth" according to the thickness of the data, but directly set it to "0 mm". Before producing the G code file, you can set the "tool lifting depth" to: tool lifting height + cutting data thickness.

3、舉個例子，刀具定在資料外表抬刀高度8mm加工的資料厚度為10mm那么“抬刀距離”值就為：8+10=18mm剩下的除了把刀具定在雕刻機臺面上外，其他操作也是不變的。

3. For example, if the tool is set on the surface of the data, the tool lifting height is 8mm and the data thickness is 10mm, then the value of "tool lifting distance" is 8 + 10 = 18mm. The rest of the operations are the same except that the tool is set on the table of the engraving machine.

玉石雕刻機工作臺

Table of jade carving machine

二、玉石雕刻機主軸發出噪音如何處理？

2、 How to deal with the noise from the main shaft of jade carving machine?

1、雜質音

1. Impurity tone

由軸承或的清潔度引起，發出一種不規則的異常音，聲音時有時無，時大時小，在高速電機上發生頻繁。

It is caused by the bearing or overall cleanliness, which makes a kind of irregular abnormal sound, sometimes not, sometimes large and sometimes small, which occurs frequently in high-speed motor.

解決方法：選用好的油脂、提高注脂前的清潔度、加強軸承的密封性能、提高安裝環境的清潔度

Solutions: select good grease, improve the cleanliness before grease injection, strengthen the sealing performance of bearing, and improve the cleanliness of installation environment

2、淅瀝淅瀝的聲音

2. The sound of pattering

由保持器與滾動體振動、沖撞產生，不管潤滑脂種類如何都可能產生，承受力矩、負荷或徑向游隙大的時候更容易產生。

It is caused by the vibration and collision between the retainer and the rolling element, regardless of the type of grease. It is more likely to occur when the torque, load or radial clearance is large.

解決方法：提高保持器精度、選用游隙小的軸承或?qū)S承施加預負荷、降低力矩負荷，減少安裝誤差、選用好的油脂。

Solutions: improve the accuracy of retainer, select bearings with small clearance or apply preload to bearings, reduce torque load, reduce installation error and select good grease.

3、嗡嗡的聲音

3. A buzzing sound

馬達無負荷運轉是發出類似蜂鳴一樣的聲音，且馬達發生軸向異常振動，開或關機時有嗡嗡聲。

When the motor runs without load, it makes a sound similar to a beep, and the motor has abnormal axial vibration, and there is a buzzing sound when it is turned on or off.

解決方法：多出現在潤滑狀態不好，以及在冬天且兩端用球軸承的馬達，主要是軸調心性能不好時，軸向振動影響下產生的一種不穩定的振動。

Solution: it often occurs in the motor with poor lubrication and ball bearings at both ends in winter, which is mainly an unstable vibration under the influence of axial vibration when the shaft alignment performance is poor.

4、噠噠的聲音

4. The sound of dada

聲音頻率隨軸承轉速而變化，零件表面波紋度是引起噪音的主要原因。

The sound frequency varies with the bearing speed, and the surface waviness of the parts is the main cause of the noise.

解決方法：改善軸承滾道表面加工質量，降低波紋度幅值、減少碰傷、修正游隙預緊力和配合，檢查自由端軸承的運轉，改善軸與軸承座的精度安裝方法。

Solutions: improve the surface processing quality of the bearing raceway, reduce the amplitude of waviness, reduce the impact, correct the clearance preload and fit, check the operation of the free end bearing, and improve the precision installation method of the shaft and bearing seat.

以上就是小編給大家介紹的玉石雕刻機臺面不平，主軸發出噪音如何處理？希望小編的總結能幫到大家。

The above is the jade carving machine table is uneven, how to deal with the noise of the spindle? I hope the summary of Xiaobian can help you.