木工雕刻機直線導軌優點和缺點

來源：http://www.840505.com 時間：2021-09-15 

1.定位精度高：使用線性滑軌作為線性導引時，由于線性滑軌的摩擦方式為滾動摩擦，不僅摩擦系數降低滑動導引的1/50，動摩擦力于凈摩擦力的差距亦變的很小。因此當床臺運行時，不會有打滑的現象發生，可達到um級的定位精度。

1. High positioning accuracy: when using the linear slide rail as the linear guide, because the friction mode of the linear slide rail is rolling friction, not only the friction coefficient is reduced to 1 / 50 of the sliding guide, but also the gap between the dynamic friction force and the net friction force becomes very small. Therefore, when the bed is running, there will be no slippage, and the positioning accuracy of UM level can be achieved.

2.磨耗少能長時間維持精度：傳統的滑動引導，無可避免的會因油膜逆流作用造成平臺運動精度不好，且因運動時間滑動不充分，導致運行軌道接觸面的磨損，嚴重影響精度，而滾動引導的磨損則非常少。故臺機能長時間的維持精度。

2. Less wear can maintain the accuracy for a long time: the traditional sliding guidance will inevitably cause poor motion accuracy of the platform due to the countercurrent effect of oil film, and the insufficient sliding of motion time will lead to the wear of the contact surface of the running track, which seriously affects the accuracy, while the wear of rolling guidance is very little. Therefore, the platform can maintain accuracy for a long time.

3.使用高速運動且大幅度降低機臺所需驅動馬力：由于線性滑軌移動時摩擦力非常小，只需較小動力便能讓床臺移動，尤其是在床臺的工作方式為經常性往返運行時，更能明顯降低機臺電力損耗量。且因其摩擦產生的熱較小，可適用于高速運行。

3. Use high-speed movement and greatly reduce the driving horsepower required by the machine: because the friction force is very small when the linear slide rail moves, it can move the bed with only a small power, especially when the working mode of the bed is regular round-trip operation, which can significantly reduce the power loss of the machine. And because the heat generated by friction is small, it is suitable for high-speed operation.

4.可同時承受上下左右方向的負荷：由于線性滑軌特殊的束制結構設計，可同時承受上下左右方向的負荷，不像滑動導引在平行接觸面方向可承受的側向負荷較輕。易造成機臺運行精度不好。

4. It can bear the load in the up, down, left and right directions at the same time: due to the special beam structure design of the linear slide rail, it can bear the load in the up, down, left and right directions at the same time, unlike the lateral load that the sliding guide can bear in the direction parallel to the contact surface. It is easy to cause poor operation accuracy of the machine.

5.組裝容易并具互換性：組裝時只要銑削或研磨床臺上滑軌支裝配面，并依建議之步奏將滑軌，滑塊分別以特定扭力固定在機臺上，既能重現加工時的告警密度。線性滑軌具有互換性，可分別更換滑塊或者滑軌神甚是線性滑軌組，臺機即可重新獲得該精度的導引。

5. Easy assembly and interchangeability: during assembly, only milling or grinding the assembly surface of the slide rail on the machine table, and fixing the slide rail and sliding block on the machine table with specific torque according to the recommended steps can reproduce the alarm density during processing. The linear slide rail is interchangeable, and the sliding block or slide rail God or even the linear slide rail group can be replaced respectively, and the machine can regain the guidance with this accuracy.

• 上一篇：泡沫雕刻機日常維護相關步驟
• 下一篇：泡沫雕刻機的噪聲要怎么處理？

相關產品：
• 
  木工雕刻機
• 
  1325木工雕刻機獨...
• 
  1325木工雕刻機
• 
  1325木工鏤空花格...
• 
  1225型平雕圓雕一...

相關新聞：
• 
  激光雕刻機和機械雕刻...
• 
  三軸雕刻機無心外圓磨...
• 
  石材雕刻機斷刀的原...
• 
  數控開料機會受到什么...
• 
  泡沫雕刻機日常井蓋如...